Centrifugal Pump Design with Capacity 50.6 L/Min for Water Utilization From Steam Trap As Boiler Feed Water
DOI:
https://doi.org/10.33603/jgst.v7i3.81Keywords:
Centrifugal Pump, Head, NPSH, Impeller, Shaft, CasingAbstract
Condensate water is the result of condensing steam which has decreased in temperature and pressure due to losses from the environment. Steam trap used to separate water or dew from steam resulting from a decrease in temperature. This condensate water has a temperature of 50°C. Based on the results of condensate water testing from steam trap it has permissible criteria for boiler feed. In the existing conditions, the boiler feed water requirement is 500 liters/hour with a temperature of 25°C, while the water produced from steam trap of 230 liters/hour so that to be able to meet the needs of boiler feed water, a pump designed with a capacity of 50.6 liters/minute is needed. The purpose of this research is to design a pump to utilize steam trap water as boiler feed water. Materials are selected according to requirements and standards. Condensate water from the steam trap becomes the initial parameter for calculating Head, NPSH, Impeller Diameter, and Shaft Diameter. NPSH available must be greater than NPSH request to prevent pump cavitation, which can cause damage or loss. Based on the calculations, the NPSH req value is smaller than the NPSH available, which is 4.62 m < 11.48 m. The total head is 7.97 meters, and the number of blades is 7. The design dimensions obtained are the impeller inner diameter of 29.47 mm, outer diameter of 72.58 mm, shaft diameter of 6 mm, casing diameter of 76.215 mm.
References
V. Antono and A. Gunawan, “Analisis Losses Pada Boiler Feed Pump PLTU Muara Karang Unit 5,” Jurnal Power Plant, 2020.
A. Yani, “ANALISIS KEHILANGAN STEAM DAN PENURUNAN TEMPERATUR PADA JARINGAN DISTRIBUSI STEAM DARI PT. KDM KE PT. KNI,” Turbo, vol. 6, 2017.
Alfa Widyawan and Ferlyn Farchlevie, “Studi Pemanfaatan Kondensat Outlet Steam Trap Sebagai Air Umpan Boiler di Pabrik Amoniak Pusri IB ,” Jrunal Rekayasa Proses, vol. 20, 2013.
Sularso, “Dasar Perencanaan pemilihan Elemen Mesin,” 2004.
Sigit Setyawan, Raditrya Putra, Ilham Satria, and Agik Dwika, “Modifikasi Proses Pengolahan Boiler Feed Water dari All Volatile Treatment menjadi Oxygenated Treatment untuk Produksi Listrik Ramah Lingkungan ,” Jrunal Rekayasa Proses, 2021.
Qomarruduin & Ilyas, “Analisis kebutuhan bahan bakar terhadap perubahan tekanan uap,” Jurnal Ilmiah Te4knik Mesin, vol. 4, no. 2, pp. 67–74, Aug. 2016.
Sularso and Haruno Tahara, Pompa dan Kompresor. Jakarta: Pradnya Pramita, 2000.
K. M. Srinivasan, “ROTODYNAMIC PUMPS (Centrifugal and Axial) Non-met allic Containment Gas o,” 2008.
T. Wibianto et al., “Prosiding The 12 th Industrial Research Workshop and National Seminar Bandung,” 2021.
A. Nugraha, “Perancangan Pompa Sentrifugal 5 Tingkat untuk Air umpan Boiler di PT BADAK NGL,” Universitas Brawijaya, 2014
Downloads
Published
Issue
Section
Citation Check
License
Copyright (c) 2023 Hesti Sekar Hesti, Ratu Fenny Muldiani, Sri Wuryanti (Author)
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution-ShareAlike 4.0 International License that allows others to share and adapt the work with an acknowledgement of the works authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journals published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Upon receiving the proofs, the Author/Editor agrees to promptly check the proofs carefully, correct any errors, and authorize the publication of the corrected proofs.
